Replacing uPVC Window Handles
Changing upvc window handles is a simple job. It is important to make sure that the new handle is fitted into the spindle cutout in the window mechanism.
If you follow the steps below any cockspur handle can fit most windows. The most important factor is the step in the height of the handle.
What to Look For
A lot of windows in the UK are fitted with uPVC handles and, over time, they may begin to show signs of wear and wear and tear. The handle of the window may become loose or difficult to operate when this happens. Anyone who is proficient working with basic hand tools is able to complete this job.
The first step is to ensure that the handle is securely attached to the frame of the window in the open position. The next step is to locate the fixing pins or screws that hold the handle in place. They are usually on the inside of the handle. They can be removed with the screwdriver and pliers.
Once the handle is loose it can be taken from its hinges by gently pulling off. Then, you'll need to find a new handle in the same dimensions and style. This can be accomplished in an online store or in a DIY store. The process should take about five minutes and requires a screwdriver is all you need.
The most important thing to consider when replacing the uPVC window handle is its step height. This is the distance between the handle's base and the place it is placed in the frame of the window. It is generally a standard measurement, and it is essential that you examine the step height of your existing handle prior to ordering a new one.
There are various sizes depending on the type of handle. Inline
handles for uPVC windows generally have 31mm lug centres as well as handles with cockspur with 43mm centres. Tilt-and-turn handles are common on uPVC Windows. They have a special design that lets the window be tilted for ventilation, and then turned to fully open the window.
The most frequent uPVC handle breakage is internal cracking rather than a breakage from the base. This can make them hard to open, and it is therefore important to make sure that any replacement handle you purchase has the same length of spindle that your current one.
Remove the old handle
Incorrectly fitted or damaged window handles may cause your double glazed windows to close or open improperly and could even result in them becoming stuck. This can be caused by various factors, such as general wear and tear on the handle or corrosion. In these instances it is essential to find replacement window handles made of
upvc window locking handles as soon as you can in order to avoid further damage and loss of function.
One of the first steps that you should do when replacing the handles on your windows made of upvc is to remove the old handle from the window. To do this, begin by getting rid of the screw that is encased when the handle is in the closed position. Once you have removed that screw, you can remove the handle. You can make the process simpler by using an electric screwdriver.
It is also important to be aware that screws can be hidden in caps made of plastic. It is best to remove the covers with a Stanley knife. After the handle has been removed, you must examine the square cut on the handle's base to make sure that the new window lock handles are compatible with it. It is important to measure the length of the spindle on the handle that was used and then compare it with the dimensions of the window mechanism spindle cutout.
There are three types of upvc handles: Espag handles with a central screw that can be turned left or right and Cranked handles with two screws, and Spade handles which are made of flat arms and can be used on either side of the windows made of upvc. Once you have found a suitable replacement, it's simply a case of screwing the handle into position and making sure that the spindle is correctly inserted into the lock mechanism. Once that is done, it should be tightened to the window frame and your replacement window handles made of upvc must be secure.
Take a look at the Spindle
If you're replacing a upvc window handle that has slipped off, it's likely because the spindle that holds it in place is loose or damaged. In certain situations, you can tighten the spindle by using pin or screw. In other cases it will require replacement completely. There are many different kinds of handles made from
upvc window handle replacement. There are three kinds of handles: inline espagnolette, tilt-and-turn, and cockspur. Each type of handle is mounted and replaced in a different way.
Before purchasing a replacement handle it is important to know the dimensions of the handle that is currently in use. This will ensure that the new handle is the right size and will fit correctly into the window. Luckily, all handles conform to industry standards of sizing making it fairly easy to find the right size.
To measure the size of the handle, turn the window to the open position. You should be able to determine the dimensions of the pin or screw that secures the handle. Then, use a tape measure or ruler to determine the length of the spindle. Once you know the length of the spindle you can buy a new spindle that is the same length.
The step height of a upvc window handle is also a factor to take into consideration when purchasing replacements. The step height is the distance from the bottom of the handle to where it rests on the frame. It is typically about 21mm or 9mm for aluminium and uPVC. Dropping something in the gap will let you observe how far the handle extends before it reaches an obstruction.
Cockspur handles often have different backset heights based on the type of window they are placed in. Inline Espag handles have a standard height of 43mm from centre to centre (2 fixing points). Cockspur handles, however have different backset heights dependent on the style of the window they're in. This is due to the fact that they have an extension spur that extends from the handle and then locks over the cockspur wedge striker plate.
Fit the New Handle
Once you've selected the new handle, align it carefully with the holes for screws on the door. Secure it using the screws provided. If you're replacing the latch lever the lever can be mounted the same way as the door handle. Then, you can attach the
external door handles euro lock trim to conceal the screws for mounting.
Tips: To remove a metal head from a wooden wedge, place the handle on the floor so that its wide end is level with the ground. Then, you can use a hammer and tap the thin end. Be careful not to scratch the handle or the spindle.
