Reasons Your
fiat 500x key fob replacement 500 Key Fob Won't Work
A
fiat 500 remote key replacement 500 key fob allows you to easily open doors and start your vehicle. However, there are numerous reasons why the fob won't be working. These include a dead coin battery damage to the receiver module, issues, and interfering.
This listing is for a NEW replacement
fiat key replacement near me Ducato key fob programming (
doodleordie.com) Flip Key Remote that appears similar to the Ilco brand. It needs to be professionally programmed (click here to search for local automotive locksmiths). It includes lock, unlock and trunk buttons.
Dead Coin Battery
A dead battery is the most frequent reason for your 500 key fob not functioning. Modern key fobs operate with a limited range of operation, and must be within a few feet of the vehicle to operate. If you're not close to your vehicle, and you press the key fob button, the car won't be able to respond, and will display the "Key Fob Not Detected" message in the instrument cluster.
If this happens you need to replace the battery of your coin-cell (Part Number CR2032) by a brand new one from a reputable brand such as Panasonic Duracell or Energizer. They are usually available in your local hardware store or on the internet.
After you've replaced the battery in the coin cell You can test it by standing next to your
fiat 500 car key cover 500 and pressing the buttons. The car will flash its parking lights and the key fob should operate the lock and unlock switches.
If the key fob doesn't function after replacing the battery, it could be damaged by water, which prevents it from communicating with the receiver module inside your vehicle. Water damage can occur in a variety of ways, from a light splash to submerging the fob in salt water at the beach. If you suspect your fob has been exposed to water, try placing it in a dry rice bag to draw the moisture out. If this fails, you'll require your fob to be reprogrammed either by an auto locksmith or a dealer.
Water Damage
Water damage can happen if you immerse the fob in the ocean or wash it in a machine. Saltwater can cause the circuit board to short and then end up dying. If you get the fob wet, it's not an ideal choice but if you accidentally drop it in a cup of water or don't remember to remove it from your pocket before you run the washing machine Don't give up hope.
First remove the battery from the fob. Before replacing the battery clean the electronic chip using isopropyl, or a similar product. Test the fob afterward to check if it's working. If the key doesn't function, it may need to be reprogrammed. This is usually done by an auto locksmith or dealer.
If your key is old and not programmed to work with your vehicle it is necessary to replace it completely. A professional locksmith for cars can complete this simple process. The locksmith will need to cut the key to match the ignition of your vehicle. The locksmith also needs to reprogram your fob into the vehicle's system. This is a cost-effective and quick process that can be completed within the same day.
Receiver Module Issues
Your 500 key fob may not function because it's out of range. The remote has a range of 30 feet, which means if you are too far from your
car key cover fiat 500 it won't respond to your commands. It's easy to remedy this by moving your remote closer to your car until it responds.
If you've replaced the coin battery (commonly known as a "button" or "watch") and the fob isn't working it could be due to an internal circuit board problem. In the majority of cases, reprogramming your fob can resolve the issue. You can find instructions on how to do this on the majority of automobiles by searching YouTube or checking out the owner's manual.
It's possible that you need to replace the metal clips that keep the coin battery in place. If they lose tension it could prevent the coin battery from sitting properly and cause your remote to malfunction.
In rare instances, the fob might be out of the vehicle's sync because of hardware or software issues. This can cause a major problem, but you can usually fix it by visiting a local dealer or auto locksmith to have them reprogram your fob for you. In certain instances, the software may also require reinstallation into your body control modules.
Interference
Interference can also cause the key fob to not receive or transmit a signal. This may happen if the keyfob is located in close proximity to a radio transmitter such as a cell phone or radar detector. Other reasons the key fob might not function may be a lack of connection to the buttons and internal chip or water damage.
If your key fob suddenly stopped working, or you have tried everything at home to fix it (e.g. battery replacement, reprogramming and using the spare key fob, it could have a faulty receiver module on your 500. The receiver module, located under the dashboard, receives radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.
There is a straightforward method to reset the 500's in-board system, including the keyfob. Disconnect the battery 12 volt for approximately 15 minutes by taking off the negative cable first then the positive cable. Reconnect the battery. This will clear out any remaining electricity and restart the car's computers. This can help you get your key fob working again. If the issue persists, you should consult an expert technician. They'll be able to identify the root cause of your issues.
