UPVC Replacement Door Handles
The handles on your doors wear out over time and need to be replaced. It is important to keep the same dimensions as the handles you have previously replaced when replacing them.
The three measurements you need to examine are the top screw position the lever and key hole sizes. Use the size guide to help you.
Inline Lever/Lever
A lever or lever door handle is a contemporary handle that can be used on replacement or new doors. This style door handle is offered in a wide range of styles and finishes. This handle is offered by several manufacturers, including Avocet ERA Fullex Hoppe Mila Millenco Yale.
Fab and Fix Windsor Inline Sprung Lever Door Handle
The uPVC/Composite door handles are made of sturdy materials and are suitable for multi point lock doors which require a robust design. The handles are inline, and they utilize the same spindle and screws to fix them. They can be easily installed on a new or existing uPVC/Composite doors.
The spring lever design allows the handle to be positioned and angled to provide a comfortable grip and is suitable for all users. The handle has been endurance-tested to 200,000 cycles. This helps ensure that the quality of finish and performance over time. The sprung lever can be reduced to accommodate the widest range of locks. This is particularly useful in doors that are narrower, where the cylinder is situated further back from the door. A lever that is shorter is an excellent option for doors where the latch could be opened by a thumb turn located on the inside.
Lever Pad
The lever pad upvc handle is different from the lever handles that are commonly found on doors. These handle types can either use a single spindle (inline) or independently from each side by using two inline or offset spindles (pad). They are usually utilized on UPVC doors with
double glazed handles double glazing handles and come in a range of finishes and variations.
The handles are available in various finishes, including White Chrome and Gold. The finish is BS EN 1670 Grade 5 and is resistant to rust. This gives the
brompton carry handle an outstanding performance and durability for its intended use.
All UPVC handle lever pads come with a spindle, screws, and can be fitted on a uPVC door. The backplate fixation centres of 211mm permit a larger handle, which is typically beneficial when replacing an
old upvc door handles or damaged multi-point door lock mechanism. These handle levers are also spring-loaded, thereby solving the issue of handles hanging out of the horizontal position when not in use.
It is crucial to match the dimensions of the PZ for both the multipoint lock and the uPVC doors when choosing the replacement UPVC spindle and handle. This measurement is also referred to as 'handle centres' or cylinder centres'. It is important for matching the correct handles.
Once you have the correct PZ size, you'll need to ensure that the lever pads and push pads are in a appropriate shape to accommodate the American with Disabilities Act (ADA) compliant handles that you require for your doors. These are usually square or round with an internal lever and an external push pad.
The majority of the
upvc door handles Lever Pads we offer are sprung. This means that they will return to a horizontal state when not being used, rather than hanging and possibly being stuck in the frame. This helps prevent the draughts and cold air from entering a property. It is also the case that the majority of UPVC handle lever pad style handles are handed that allows you to put them on either side of the door.
Euro Cylinder
Cylinder locks are typically found on uPVC doors, but they can also be used on other types of door. The cylinder lock is operated with a key that unlocks the cylinder's case. This exposes pins that can be aligned to those inside the lock, allowing them to turn the revolving camera, thereby opening the door. Euro Cylinders are available with up to six pins. Internal and external doors require different levels of security.
The selection of a cylinder is vital. It depends on the use that your doors and handles will receive. For example, external doors must be secured with a higher security cylinder, whilst internal doors can be secured using the standard cylinder. Some cylinders have extra features that increase security, such as anti drill or anti bump properties.
A euro cylinder should be measured correctly to ensure it is the right size for your door. The cylinder should be measured from the screw hole at the center to the ends of the cylinder. This includes the thumb turn, should there be one. It is best to do this while the lock is in place however, if this is not feasible, you can take it off and remove it to take measurements. A cylinder that is protruding beyond the handle and escutcheon may be susceptible to attacks like snapping locks, therefore it is crucial to make sure it's not too long.
Most modern cylinders are made with bump and anti-drill features that are built into their design. These are designed to reduce the chance of a attack by forcing the cylinder rotate in a different direction. This can help deflect the attack, and protect your door.
Certain cylinders are constructed to resist snapping. This is a more frequent kind of attack on cylinders where the break line in the lock is smashed by a tool that is specially designed to break off the front of the cylinder to allow the door to open. This is faster and easier to achieve than opening the door with a multipoint lock and leaves no evidence of a break-in which could hinder the insurance claim.
Spring Cassette
The spring cassette is positioned in the base of your door handle's backplate, providing a spring solution and returning your multipoint lock handles to their rest position after use. The handles were previously equipped with no spring and would drop when the locking mechanism was removed. This simple feature is one of the best ways to correct this, and is an excellent way to stop your doors made of upvc from getting stuck in the open or closed position, as they aren't always easy to close manually.
These spring cassettes have been specifically made for use with multipoint locks that are sprung but they won't work with non-sprung multipoint handles. You will require a bespoke hole cut into your backplate in order for them to fit (please look at the image for a technical diagram). These cassettes are a replacement to damaged or missing cassettes in the backplate of uPVC
patio door handle locks handles. They are supplied in a single unit. They have a square-cut out that is able to accommodate an 8mm shaft.
These spring cassettes provide an excellent value solution to the problem of door handles that have become sagging. These spring cassettes are simple to install and will extend the lifespan of your uPVC door. Please contact our team to learn more about our range of uPVC accessories and spares. We are available to help and happy to offer expert advice.
