Choosing Upvc Window Replacement Hinges
Choosing and fitting upvc window replacement hinges isn't as complicated as you may think. Check that the hinges' arrows face in the correct direction, and then measure the thickness of the hinge arms on the opening frame (13mm or 17mm).
There are a variety of different kinds of hinges, each with their distinct characteristics. This article will discuss the most popular uPVC hinges, as well as their advantages.
Egress/Easy Clean Hinge
They are a great option for replacing or upgrading your fire escape safety windows because they can open to a full 90-degree angle. They can be disengaged in an easy-cleaning position, allowing you to access the windows' exterior without the need to climb ladders or lean over dangerous angles.
Yale is among the most reputable and well-known brands in the field of home security. These hinges are compatible with any type of uPVC side-hung windows. They can be moved into the clean position by pressing in a small button and then sliding the window sash over to one side. Once closed, the window sash will revert to its original position.
Both 13mm and 17mm sizes are available. Use our Egress Selection Guide to help you determine the best product for your window.
These hinges are designed to be used in conjunction with a standard side-hung frame, either uPVC or aluminium. The friction screw is used to adjust the resistance. This makes opening the windows more simple and reduces the chance of accidental closing during strong winds. They have been tested for more than 30000 cycles and are in compliance with British Standards approved BS EN 130126-6:2008 and BBA/Secured by Design.
The Nico Egress Easy Clean
friction hinges uk hinge is easy to operate and does not have buttons or catches. It provides a convenient and safe option for emergency exit and cleaning. First, open the door to the egress (full opening) position, then press the hinge retaining clip located on the inner side of the bottom corner. This will open the bottom and top catches and allow you to slide the sash into the easy-clean position. Once it is in the easy-clean position close the window to reset the hinges back to their original position.
Fire-Escape Hinge
Fire Escape Hinges are often referred to as "Easy Clean" hinges are used to replace windows that open sideways for escape (fire safety) reasons. These types of
double glazed hinges are more spacious and more efficient than conventional hinges to provide an open space to escape in the event of a fire. This type of hinge is a legal requirement in any living space that has windows, as stipulated by building regulations.
They have an exclusive friction stopper that allows the window to open at an angle of 90 degrees. It allows the opening sash to slide across when it is open to allow easy cleaning of the external side of the glass without having to climb ladders. The hinges do not have catch or buttons and are operated by an easy, secure lever that can be accessed from the inside of your home.
The hinges, made in the UK by Cotswold are fitted with the safety of children in everyday use. This can be overridden with a hidden button. You'll have peace of peace of mind knowing that your children won't open the windows too wide. They are available in 13mm and 17mm stack heights.
Find the length of the side-hung window hinge that is attached to the frame. (See the article on measuring upvc window hinges). Then select the correct size hinge from the options below.
Please note that the measurement is taken from the part that is fixed to the frame and not the sash. The actual hinge length could be shorter or larger based on the manufacture of your old windows. When deciding on the width of the hinge, most frames made of upvc will have a stack height of 13mm, but if your old window frame measures 17mm, choose this option. You can also install the 4mm packer to make up the difference. All the hinges are supplied in pairs (1 left and 1 right). Screws are not included in the hinges. If needed, they can be purchased separately. Our window
repair door hinge screws made of upvc are recommended. These screws are designed to enhance the performance of your hinges and allow them to work efficiently for a longer. They have a reduced friction design, and an improved weather seal that is fitted with a new nylon reducer cap.
Restricted Hinge
Standard hinges can make it difficult to open a window fully. The restricted child safety friction hinges can help overcome this problem and are a great solution when ventilation is required but access for cleaning or escape in case of fire is not possible. They limit the number of times you can opening the sash and allow for the bypass of this restriction by pressing the button. They are suitable for both side- and top-hung windows. They are available in 17mm and 13mm stack heights.
The Nico Restricted Egress Friction Hinge blends the characteristics of a standard restrictor and an escape hinge to offer an efficient and easy way to meet building regulations. It is available in 13mm and 17mm stack heights and is suitable for the top and side openings of uPVC window. It comes in two pieces that has one hinge which is the one that is restricted for egress, and the other being the unrestricted. This permits one hinge to be installed at the bottom and the other is set on top.
These uPVC hinges are made to be used with windows that aren't able to be fully opened, for instance bedrooms for children. The mechanism limits how far the sash opens to an appropriate height of 100mm, and re-engages once the window is closed.
Like the other kinds of
uPVC friction hinges they can be installed on all types of windows and are suitable for difficult to access windows above ground level three-storey flats and those that would normally require a ladder to reach them. They can be combined by our security enhancements like hinge guard protection plates or dog bolts to offer PAS 24 performance.
When replacing a hinge on a window, it is important to determine the length of the current hinge to ensure that you order replacements that match in size. The most efficient method to accomplish this is by looking at the hinge in the image gallery and determining the best place for it to be placed. Top-hung hinges are limited on both sides, while side hung hinges are restricted to one side.
Standard Hinge
Standard hinges have metal-to-metal contacts and don't require additional components to reduce friction. It is available in a variety of finishes, and is fire-rated. To determine the radius of your hinge lay it flat and align with a quarter and dime in two corners. If the quarter is more snug then the corner should be round to 5/8 inches.
The right hinge can make or ruin the appearance of your door. Achieving the same design and style of the hinges to your door will create an attractive and well-integrated look.
