Replacing uPVC Window Handles
It is easy to change the handles on windows made of upvc. The important thing is to make sure that the new handle is a good fit for the spindle carved out in the window mechanism.
If you follow the steps below, any cockspur handle will fit most windows. The height of the step of the handle is key.
What to Look For
As time passes, uPVC
Handles for double Glazed doors on many windows in the UK begin to show signs of wear and wear and tear. If this occurs, the window handle could become shaky or difficult to operate, which makes it essential to replace it. This is a relatively simple task that can be accomplished by anyone who is familiar with basic hand tools.
The first step is to ensure that the handle is securely attached to the frame of the window and in the open position. The next step is to locate the screws or pins that secure the handle in place. They are usually located on the inside face of the handle. They can be removed with a screwdriver, or pliers.
Once the handle has become loose It is best to gently pull it away from its hinges. It is then necessary to locate a replacement handle that is the same design and size. This can be done on the internet or at a local DIY store, and should take five minutes using an screwdriver.
One important factor to consider when replacing a uPVC window handle is the step height. This is the distance from the bottom of the handle to where it is placed on the frame of the window. This is a common measurement and you should check the step height before ordering the replacement handle.
Depending on the type of handle you have there are various sizes that are available. Inline handles for
upvc sliding door handle windows generally feature lug centers of 31mm, and there are also cockspur handle types that have 43mm centres. Tilt and turn handles are often used on windows made of uPVC, and they have a special design that allows windows to be slid up for ventilation, and then rotated to open the window completely.
The most common uPVC handle breakage is internal cracking, rather than a fracture from the base. This makes them difficult to open and is why it is crucial to ensure that the replacement handle you purchase has the same spindle length as the one you have.
Remove the Old Handle
If the
handles for patio doors on your windows are damaged or improperly fitted, they could cause double-glazed windows to open and close incorrectly. They could even become stuck. This can be caused by various reasons, including general wear and tear on the handle or corrosion. In these instances it is essential to replace the window handle as soon as you can to prevent further damage or loss of function.
When replacing the handles on windows made of upvc, you should remove the handles that were previously installed from the window. To do this, begin by getting rid of the screw that is covered when the handle is in the closed position. This will reveal a screw and once removed, you are able to begin to remove the handle itself. It is a good idea to use an electric screwdriver for this as it will make the task much easier and quicker.
You should also be aware that screws may be hidden in caps made of plastic. It is best to remove the covers using the help of a Stanley knife. After you have removed the old handle, you will need to check the square cutout on the base to make sure that the new handle for the window lock is compatible. This is important because you'll need to measure the length of the spindle on the old handle to make sure it is in line with the size of the window mechanism and the handle spindle cut out.
There are three kinds of upvc handles: Espag handles with a central screw that can be turned left or right and Cranked handles with two screws and Spade handles that are made of flat arms and can be used on either side of the window made of upvc. It is easy to
replace upvc window handle the handle after you have found one that is suitable. Just screw it into the frame, and make sure the spindle is inserted correctly into the lock mechanism. After that, you can then tighten the handle to the window frame. Your replacement upvc handles should now be secure.
Take a measurement of the Spindle
If you're replacing a Upvc window handle that has slipped off, it is likely due to the spindle that holds it in place has become loose or damaged. In certain situations you can tighten the spindle with a screw or pin. In other cases it will have to be replaced completely. There are a variety of handles made of upvc. There are three kinds of handles: inline espagnolette tilt-and-turn, and cockspur. Each handle type is installed and replaced in a different manner.
It is essential to measure the current handle before purchasing the replacement. This will ensure that the handle fits the
window handles for wooden windows in a proper manner and will be of the correct size. All handles are sized in accordance with industry standards, so it is easy to identify the correct size.
To measure the size of your handle first, remove it from the window by turning it to the open position. You should be able to determine the dimensions of the screw or pin that secures the handle. Then, use a ruler or tape measure to determine the length of the spindle. Once you have the length of your spindle, it is possible to buy a replacement of exactly the same length.
The step height of a window handle is also important to take into consideration when buying an alternative. The step height is measured from the base to the point where the handle is positioned on the frame. This is usually approximately 21mm or 9mm in aluminium and uPVC. To ensure that the new handle is suitable the gap, drop something into the gap to see the distance it will go before meeting an obstruction.
Cockspur handles often have different backset heights, based on the style of window they're installed in. Inline Espag handles come with an average height of 43mm from centre to centre (2 fixing points). Cockspur handles have different backsets depending on the type of window they are located in. This is because they have spurs that extend from the handle and is secured over a cockspur wedge striker.
Install the New Handle
Once you've selected the new handle, make sure it is aligned with the holes for screws on the door. Secure it using the screws supplied. If you're replacing the latch lever it can be put in the same way as the
patio door handle with lock handle. Then, you can attach the door trim to conceal the mounting screws.
Tips: To remove the metal head from a wedge made of wood, place the handle on the floor, so that its wide end is on the floor. Then, you can use to tap the narrow end. Be careful not to damage the handle or the handle spindle.
