How to Change a Subaru Spare Key
Call a locksmith if you are missing your
subaru chip key replacement key. Locksmiths are usually able to cut you keys at a lower cost than the dealer.
Fob remote "push to start" intelligent keys or a simple metal key are the two most common kinds of
Subaru car keys. The Fob key has an embedded chip and must be reprogrammed.
Keyless Entry System
A key fob can be used to lock or unlock your Subaru from a distance. It can even unlock the trunk or lift gate of your vehicle. These remotes function with an inside keypad to communicate with the vehicle's computer system.
Some models of Subaru offer a little-known feature called PIN Code Access. You can utilize a personalized number sequence to start and unlock your vehicle. Refer to the owner's manual for learn how to use this feature if you have a Subaru Forester, Outback Crosstrek, WRX STI or Impreza.
It's likely that the battery inside the key fob has gone out. You can check the battery life of your key fob by using an instrument that is portable or a multimeter in your garage.
The next step is to take the key fob out of its case, and then examine the circuit board that controls the transmitter. The board will contain one or two sets of 8-digit numbers, so write down the first set so that you are able to recall it later. After you've done this you can begin programming the key fob at home. The procedure to do this differs based on the make and year of your vehicle but it's usually easy enough to complete yourself.
Key Fobs
Reprogram Subaru Key's newest models are all equipped with key fobs that not only unlock the doors, but also turn on your lights, lock the gas cap, and even start your vehicle. This last feature is particularly useful if you have ever encountered yourself at the gas station and your car won't even start because the battery in the key fob has died.
No matter if your Subaru is brand new or old you can be sure that the key fob can be replaced with no difficulty. Keep in mind that some of the most modern models, with the latest technology, may require a visit to the dealer. With just a bit of effort and time, you can create your own replacement key fob.
Start by opening the case and looking at the circuit board of the transmitter. (Instructions on opening the case are usually found in the owner's guide). It should have one or two sets of serial numbers each of which is 8 digits long. Keep the first set of numbers for later for reference.
Then, sit in your driver's seat, and close all the doors. Turn the key to start the vehicle and then switch it off after ten turns. Press the lock button of your key fob, and then open the door. This will test that your doors are working properly. Then, close the door and remove the key from the ignition. You should hear your vehicle sound again, signalling that the key fob is programmed.
Ignition System
The key battery could be dead If your Subaru keys aren't functioning as they should. You can replace the key fob battery at home if you are familiar with the procedure. A replacement battery is cheap and is fairly easy to locate. If your key fob won't respond to your commands, there could be another problem. If you want to get a replacement key, it's advisable to visit a dealer. They can ensure that the key is an original Subaru key that is under warranty, and that it is programmed to your vehicle. This is much safer and more convenient than purchasing an aftermarket key from a company online.
You can also ask the dealer cut a brand new key if you provide them with your VIN number and proof of ownership. They'll use this information to create a code for the
replacement key subaru key in order to be accepted by your immobilizer. This process is more complex than cutting a new one, and the dealership will usually charge more for this service.
Once the new key has been programmed then you'll be able change it over to your existing key. You'll only have five seconds to insert the second key, so it's essential to keep an active key in your bag. Once the security light ceases to flash, you can remove the new key and test it to make sure it's working properly.
Battery Replacement
One of the primary features that make Subaru fobs so valuable is their ability to switch on your car's power windows as well as sunroof with a single touch of a button. The battery inside your Subaru fob isn't intended to last forever, and it will require replacement at some point. Fortunately, replacing the battery is a simple process that you can complete yourself with the help of this quick guide from Capitol
subaru key programming.
To begin the process, you'll have to find the small crevice in the seam that separates the front and back of your key fob. You can open this seam with a flathead screwdriver to reveal the small compartment that houses the battery. Take out the old battery and then install a new one, making sure it is facing the right side upwards. Once you have assembled everything is in place, you can use your new key fob for locking, unlocking, and starting your vehicle.
It's always an excellent idea to keep an additional set of keys at hand particularly if you've lost them or they're not functioning properly. You can buy a new key at your local dealership or get it cut by locksmiths. It is essential that your key fob is working correctly as soon as you can to ensure that you are able to drive safely.
