How to
Repair Bifold Door Top Roller Guide
If your bifold door is sticking then it's likely that they need some attention. They could require cleaning, lubricated or adjusted. The problem could be caused by loose bolts on the top pivot or by the top guide roller.
This kit contains all the hardware you require to restore your
bi fold door repair-fold wardrobe door to its optimal performance.
Take the door off
It may seem complicated and difficult to set up a set of bifold internal doors but for DIYers with some experience it's actually quite easy. Getting the frame into position isn't a problem; the tricky part is getting the doors to fold and close easily and accurately. Bifold doors are a complex piece of machinery, and as such, they might need some tuning up to ensure that they function properly. It could be as easy as tightening a screw or as complex as taking out the door and replacing the pivot pin or roller.
The majority of the time, you can solve these issues with a few simple adjustments, without having to remove the doors. It is possible that your bifold doors are sliding, scraping the floor or bouncing off the track. Getting these issues under control isn't difficult, and with three simple steps your
repair bifold door top pivot doors can be back on track in no time.
One of the most common issues that internal bifold doors encounter is sliding out of alignment. This can be due to loose screws, holes in the anchor/pivots or a misaligned bifold door. In most instances, you can fix this issue with a few simple adjustments, however if the door isn't moving at all, it might need to be removed and replaced.
You'll need to remove the door with a screwdriver, and possibly pliers to loosen any pivot pins that are tight. The screwdriver is used to break any locking levers on the bottom bracket of the pivot, and the pliers will let you wiggle the pin out and off.
Once the top roller has been removed Once the top roller is removed, you can raise the door, turn it down and remove it from its track and pivot brackets. It's usually a simple procedure, but be careful to not let the door strike the frame of the door. Then, you can sand down the edges of the door to make it smooth. You can then paint or refinish the door if necessary.
Remove the Roller Guide
This spring-loaded roller is mounted on top of bifolding doors to facilitate smooth operation. It is designed to work with Kenna frames and can be fitted to a door panel 1 to 1/8 inch thick. It is made of nylon, steel, and plastic components. It can replace the damaged guide.
Remove any screws holding the roller guide in place with the screwdriver. Use your hands to slowly lift it off the frame. This may require some effort, so you should have an assistant help you keep the door in place as you remove it.
After removing the guide, carefully cut off the remaining finishing on the guide's foot using a razor to separate it from blank rod. This will make it easier to take off and protect the new guide foot. The guide foot is extremely sharp and could cut or snag fingers.
It is likely that you will need to use some force to pull the guide off, but be cautious not to break or chip the foot. After you've removed the guide, you must remove any threads or epoxy left in the place where it was anchored. This will help prevent any future problems with the guide.
After removing the guide, test your replacement by putting it in its permanent position. Apply a few rotations with masking tape or guide tubing to hold it in position. This allows you to double check the alignment of your guide and spacing to make sure everything is in place. This is vital to avoid future problems, whether you use the CRB Spine Finder & Deflection System or simply eyeball it.
If the guide is set properly and functions as it should the next step is to reinstall the door in place. Make sure that any screws or pins that you removed or loosened must be replaced and tightened appropriately when you're done.
Take the Bottom Pivot off.
Bifold doors make a gorgeous addition to any home, but sometimes they require some tweaking or adjustment to stay in good shape. Some issues can be resolved by keeping the doors in place. Others will require the doors be removed. This guide will walk you through the steps to remove internal bifold door pivots, pins and rollers so you can make your doors slide like new.
The first step is to gather your tools. Making sure you have everything in place prior to time will help you avoid a lot of frustration later during the construction. You'll also require an plier and a screwdriver. You can pick up a set of basic tools at your local hardware store at a reasonable price. It's important to have some wood glue on hand. This is useful if you need to fix the rollers into the right place.
After gathering your tools and tools, open the
bifold door repair bracket door and loosen the top track bracket by using your screwdriver. Once the bracket is free, you'll be able to lift the door off of the top track. It could take a little bit of jiggling but it should be able to pop right off the track.
The pivot on the bottom of the frame will have to be removed. Close all doors in the interior before you begin. This will be much easier than trying to work from inside. If the track on the bottom is still in good condition it will be possible to lift the door and then remove the track.
You will need to replace the track if it is damaged. Hardware stores offer replacement tracks for bifold doors, as well as swinging closet doors. If the track is seriously damaged, then you might need to replace it entirely.
Once your track is repaired or replaced You'll need to test the doors for the proper operation. Make sure they're able to move smoothly in and out of position. You should also ensure that the edges of the door are parallel to the frame when it is closed. If they're not, you'll have to adjust the top pivot bracket by tightening or loosening the bottom setscrew.
Replace the Roller
Bifold doors are a great way to enclose closets, laundry nooks and pantries, but only if they work properly. They are made up of two panels that hinge together and open up on a track that sits in the top of the frame. Over time, the roller guide bearings could wear out and cause the doors to bow and scrape against the floor. The roller guide can be replaced in just a few minutes with basic tools.
The first step is removing the guide for your roller from the door panel. The bottom pivot bolt must be removed, and the screw that holds the guide to the top of the door panel must be loosen. Once the guide is removed, lift the door panel up and off its track. Then, loosen the nut that holds the top pivot bolt and employ the wrench to remove it from the hole in the top header of the door frame.
A replacement top nylon roller guide that has a 7/8 inch diameter wheel and a base made of steel is available from Stanley, Cox or Acme. It mounts on the top of the bifold door, which is 1 to 1-3/8 inches thick and comes spring-loaded to self-adjust in the upper track for smooth gliding.
Another issue with a bifold door is that it scrapes the floor when it is closed or opened. This can happen after adding carpet or other flooring materials that require the doors to be raised slightly to allow for clearance. The removal of the bottom pivot adjustment screw and loosening the top track's mounting screws and moving the anchor pin usually enough to clear this issue.
A new set of roller guides is a cost-effective solution to your
bifold door roller replacement doors being difficult to operate. They're usually available at the hardware store near you in the door section, but they're also available on the internet through a variety of sellers. You'll also require the squeeze-clamp and a tiny container of Elmer's wood glue, which can be found in large box stores. The clamp is used to keep the
repair bifold door top roller area in place after the glue has been inserted and allowed to dry.
