Peugeot 208 Key Replacement
It is best to delegate the replacement of Peugeot 208 keys to auto locksmiths that have the equipment and knowledge. They can make and program new keys much faster than a dealership would and at a lesser cost.
If your key fob has stopped locking or unlocking your doors it could be due to a dead coin battery. However, there are many other reasons that the key may be malfunctioning.
Dead Coin Battery
A dead coin battery will prevent your Peugeot 208 from locking or unlocking, and will not allow you to start the engine. If this is the case, you'll have to apply the backup starting technique that's described in the owner's manual for your vehicle.
Another reason why your 208 might not start is because the spark plugs are worn down. The spark plugs light the fuel to start the engine. They have a limited lifespan. They'll eventually fail when they aren't used enough.
Luckily, there's an easy solution to this issue. The best solution is to measure the voltage of your car battery using a multimeter. If the voltage falls below 11,5 volts, then it's time to replace it. If the battery has corroded, it is important to clean its contacts. This can be accomplished by removing the rubber cover from the two battery terminals, and then using a wirebrush to remove any corroded battery parts. Then, you should reconnect the positive and negative pole cables.
Water Damage
If your 208 doesn't start and the battery is not flat then you should check that the spark plugs are working. It could be that they are overly filthy, making them unable to spark. The spark plugs can be cleaned in a workshop.
Peugeot cars are equipped with keys that are transponder-type and works with the car's ignition system. This ensures only the correct key is able to turn the engine. If the chip inside the Peugeot key is damaged, then it will not transmit the proper signal to the vehicle.
Water damage is a frequent cause of this problem. This is most common in colder climates, where the vehicle might have been exposed to rain or snow. In this case, you need to contact an experienced locksmith who will have the required tools and equipment to reprogram the key. They will also have the latest technology and equipment needed to make the Peugeot 208 smart key. The process shouldn't last more than 15 minutes.
Contacts to the battery are not working properly.
peugeot 208 key fob not working changed from the old carbon-encased transponder chips to an entirely new kind of chip that utilizes electronic components within circuit boards. This new technology works great when it's brand new, but over time the circuit boards begin to deteriorate and stop working properly.
This could prevent the immobiliser's function from being activated, meaning your vehicle won't start. If this happens it's a good idea seek out a Peugeot specialist or locksmith.
Another common issue is when the battery in the key fob gets depleted, which causes the key blade to stop from entering the lock. A locksmith from your vehicle can replace the battery and cut a new blade for you, this is typically a quick fix.
Faulty Receiver Module
It could be that the receiver module has a problem If your Peugeot key fob doesn't work after being dropped on the floor, or exposed to a sudden rainstorm or accidentally washed. The receiver is responsible for transmitting radio frequency signals to an on-board computer that controls the central locking system of your
peugeot key repair vehicle.
The key fob itself has rubber seals that block water from reaching the electronic chip inside. Water can damage the chip if it is exposed to water for a prolonged period of period of. The high salt content of the ocean water or pool could cause damage to the key fob, especially if it is submerged.
The module needs to be replaced if your Peugeot spare key isn't working anymore. This is only done by an expert auto locksmith or Peugeot specialist.
peugeot partner key fob replacement 308 key replacement (
blog post from Alonegocio) keys like other cars are secured by an immobilizer device. This requires the proper code to begin the car. This is the reason that you should only rely on the Peugeot locksmith to design and program a
replacement key for peugeot partner van.
Computer on board is not working properly
The on-board computer inside your Peugeot is responsible for a number of the systems within the car, from power windows to the airbags. When something goes wrong in these systems, they will usually display a code that identifies the problem. The code will be stored within the system until the problem is fixed. Most often, this involves replacing the on-board computer.
The most common reason for the warning light of the airbag to flash is corrosion or loose connections within the sensor. This could be due to wear and tear, ageing or exposure to moisture and salt. It is imperative to have this issue resolved as soon as you can, since a malfunctioning airbag can be risky in the event of an accident.
If your Peugeot is showing a card not detected error, the battery inside the key fob could be weak or dead. This prevents the key fob from transmitting a signal that will disable the standard immobilizer in your vehicle. You can test this by pressing the unlock button on the key fob, then attempting to start your car. If it doesn't work it is because the battery of the key must be replaced.
