Reasons Your
fiat panda key 500 Key Fob Won't Work
A key fob from
fiat 500 abarth key fob replacement 500 is a convenient way to unlock the doors and start the car. However, there are many reasons why the fob may stop working. This includes a dead coin-battery or water damage, problems with the receiver modules, and interference.
This listing is for an NEW replacement
fiat punto key replacement Flip Key Remote that is similar to the Ilco brand. It needs to be professionally programmed (click here to search for local locksmiths for your vehicle). Includes lock, unlock, and trunk buttons.
Dead Coin Battery
A dead battery is the main cause of your 500 key fob being inoperative. Modern key fobs come with a limited operating range, and must be within only a few feet from the vehicle to function. If you're not close to your vehicle, and you press the key fob button the car won't respond and will display the "Key Fob Not Detected" message in the instrument cluster.
If this happens you need to replace the battery of your coin-cell (Part Number CR2032) by a new one of a reliable brand, like Panasonic Duracell or Energizer. They are usually available in your local hardware store, or online.
After you've changed the battery on the coin cell, you can test it by standing next to your
fiat 500 replacement key uk 500 and pressing the buttons. The parking lights should flash and the key fob will operate the lock and unlock switches.
If your fob's key does not work after replacing the battery, it could be water damage that is preventing it from interacting with the module inside your vehicle. Water damage can occur in a variety of ways, from the slightest splash to submerging the fob into salt water at the beach. If you believe your fob was exposed to water, place it in a rice bag to draw out the moisture. If this doesn't work, your fob may need to be
reprogrammed by a professional auto locksmith or dealer.
Water Damage
Water damage can occur if you submerge the fob in the ocean or wash it in a washing machine. Saltwater poses a particular risk to the fob's circuit board which causes it to short out and eventually end up dying. It's not a good thing to submerge the fob in water however, don't give it up when you accidentally drop it in water or fail to remove it from your pants pocket.
First take the battery off the fob. Clean the electronic chip using isopropyl ethanol or a similar product and then dry it thoroughly before replacing the battery. Test the fob afterward to see if it is functioning. If the key doesn't work, it might need to be reprogrammed. This is usually handled by an auto locksmith or dealer.
If your key is a bit older and is not programmed for your vehicle You will need to replace it completely. A professional locksmith in the automotive industry can do this job. The locksmith must cut the key to match the ignition of your vehicle. The locksmith also needs to program your fob into the car's system. This is a simple and cost-effective procedure that can usually be completed on the same day.
Receiver Module Issues
One of the main reasons why your 500 key fob might stop functioning is that it's out of range. The remote has a range of 30 feet. Therefore, when you're too far from your car it will not respond to your commands. This can easily be resolved by moving closer to your vehicle until it begins responding.
If you've replaced the battery on your coin (commonly known as a "button" or "watch") and the fob won't work it could be due to an internal circuit board problem. Reprogramming the fob usually resolves this issue. You can find instructions on how to do this for the majority of automobiles by searching YouTube or checking out the owner's manual.
It could be necessary to replace the metal clips that hold the coin batteries in their place. If they loose tension it could hinder the battery from sitting properly and cause the remote to malfunction.
In rare instances, the fob might be out of the vehicle's sync because of hardware or software problems. This could cause a significant headache, but you can usually resolve this issue by visiting an auto locksmith to have them reprogram your fob. In some cases, the software may also need to be reinstalled in your body control modules.
Interference
In addition to a dead coin battery The key fob may not be receiving or transmitting signals due to interference. This could occur if the keyfob's location is in close proximity to a radio transmitter like a cell phone or radar detector. Other reasons why the key fob could not function include a poor connection to the buttons, damage to the internal chip or water damage.
If the key fob has stopped working one day without notice, or after trying every option at home to resolve it e.g. replacing batteries, reprogramming or using the spare key fob, you might have a defective receiver module on your 500. The receiver module is situated under the dash and receives the radio frequency signals from the key fob. Then, it converts them into electronic commands that the vehicle interprets.
Fortunately, there's an easy method to reset every single system on board in your 500 keys, including the key fob. Disconnect the 12 volt battery for about 15 minutes by removing the negative cable first then the positive cable. Then reconnect the battery. This will get rid of any remaining electricity and then restart the car's computers. This could allow you to the key fob to function again. If the issue continues, you should seek out an expert technician. They'll be able to determine the root of your issue.
